Home
UV  and IR Flame Detector (Ex)
Reflective Beam Detector
Addressable/Intelligent  fire alarm
Conventional Fire alarm series
Promotional products
Domestic fire alarm
Addressable Fire Alarm System
Conventional Fire Alarm System
Product Catalog
Battery Powered smoke detector
Conventional Smoke Detector
Conventional Heat Detector
Conventional Fire Alarm Control Panel
Fire Fighting System
 Manual Call Point bell strobe
Gas Detector and Co Detector
4wire detector with relay output
TC Addressable fire alarm system
Infrared Alarm System
Addressable Fire Alarm System
News
Contact Us
Documents

Product Catalog 

 

Smoke Detector conventional 2-wire EN54-7 approved

  •  Smoke Detector conventional 2-wire EN54-7 approved
  •  Smoke Detector conventional 2-wire EN54-7 approved
  •  Smoke Detector conventional 2-wire EN54-7 approved
  •  Smoke Detector conventional 2-wire EN54-7 approved
Model No.︰YT102
Brand Name︰ZC
Country of Origin︰China
Unit Price︰US $ 6.5 / pc
Minimum Order︰100 pc
Share on:

 Total 6 Related Items 
12345Next
Auto next page:   SecondsPlay

Product Description

2-Wire Conventional Photoelectric Smoke Detector 

GENERAL DESCRIPTION

The device is photoelectronic detector uses a state of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with most conventional fire alarm control panel.

Two LEDs on each detector provide local 360° visible alarm indication. They flash every 3~5 seconds indicating that power is applied and the detector is working properly. The LEDs latch on in alarm. LEDs will be off when a trouble condition exists indicating that the detector sensitivity is outside the listed limit. The alarm can be reset only by a momentary power interruption. 

Specifications

Operating Voltage Range:             9 to 28VDC Volts Non-polarized

Standby Current:                   60µA @ 24 VDC

Maximum Alarm Current (LED on: ) 30mA @ 24 VDC

Operating Humidity Range:          10% to 93% Relative Humidity, Non-condensing

Operating Temperature Range:         14°F to 122°F (-10°C to50°C)

Adjustable Sensitivity:             0.150.3dB/m

Height:                           2.2˝ (55 mm) installed in Base

Diameter:                              4.0˝ (103 mm)

Weight:                          5.5 oz. (155 g)

INSTALLATION

NOTE: All wiring must conform to applicable local codes, ordinances, and regulations.

NOTE: Verify that all detector bases are installed, that the initiating-device circuits have been tested, and that the wiring is correct.

Remove power from initiating-device circuits before installing detectors.

1. Wire the sensor base per the wiring diagram, Figure 1.

2. Install the sensor into the sensor base. Push the sensor into the base while turning it clockwise to secure it in place.

3. After all sensors have been installed, apply power to the control unit.

4. Test the sensor(s) as described in the TESTING section  of this manual.

5. Notify the proper authorities that the system is in operation.

 

Payment Terms︰T/T,WU,PAYPAL
Product Image





Related Products
EN54-7  Conventional Smoke Detector with Photoelectric sensor
EN54-7 Conventional Smoke Detector with Photoelectric sensor
US $ 7
Smoke Detector YT102
YT102 Conventional Photoelectric Smoke Detector
US $ 8
2 wire smoke detector yt102c
2-wire Conventional Photoelectric Smoke Sensor YT102C
US $ 6.9
smoke detector YT102 Conventional Smoke Detector
smoke detector YT102 Conventional Smoke Detector
US $ 8

Home  |  UV and IR Flame Detector (Ex)  |  Reflective Beam Detector  |  Addressable/Intelligent fire alarm  |  Conventional Fire alarm series  |  Promotional products  |  Domestic fire alarm  |  Addressable Fire Alarm System  |  Conventional Fire Alarm System  |  Product Catalog  |  News  |  Contact Us  |  Documents  |  Sitemap  |  Mobile Version
  English     简体版     繁體版
Powered by DIYTrade.com